Geometry

Roof pitch calculator

Turn a measured rise and run into x/12 pitch, degrees, slope percentage and the slope factor used for roof area.

Inputs

in
Vertical height gained. May be zero for a flat roof.
in
Horizontal distance over the same span. Must be above zero.

Use the same unit for both. Inches are the default and the result is always expressed as rise per 12. A run of zero is rejected because it divides by zero.

Results update as you type.

Result

6/12 L1 · Pitch as rise per 12 of run

L1
Rise
6 in
L2
Run
12 in
L3
Slope ratio, rise ÷ run
0.5
L4
Angle
26.57°
L5
Slope factor
1.118
L6
Slope as a percentage
50%

Angle = arctan(rise ÷ run). Slope factor = √(run² + rise²) ÷ run. Rise may be zero; run must be greater than zero.

Calculated from the inputs on this page. Sources checked 21 Nov 2026.

The slope factor is the useful number. Multiply a flat footprint by it to get sloped roof area at that pitch.

How this is calculated

Pitch is usually written as inches of rise per 12 inches of run. Whichever units you measure in, the result is scaled to a 12-inch run:

rise per 12 = (rise ÷ run) × 12
angle      = arctan(rise ÷ run)
slope %    = (rise ÷ run) × 100
factor     = √(run² + rise²) ÷ run

For 6 inches of rise over 12 inches of run: 6/12, an angle of 26.57°, a 50% slope, and a slope factor of 1.1180. The factor means one flat foot becomes 1.118 feet measured along the slope.

Pitch chart

Angles and factors below are computed from the same formulas the calculator uses, not copied from a table.

Rise per 12 inches of run, converted to degrees, slope percentage and slope factor
PitchDegreesSlopeSlope factor
0/12 0° 0% 1
1/12 4.76° 8.33% 1.0035
2/12 9.46° 16.67% 1.0138
3/12 14.04° 25% 1.0308
4/12 18.43° 33.33% 1.0541
5/12 22.62° 41.67% 1.0833
6/12 26.57° 50% 1.118
7/12 30.26° 58.33% 1.1577
8/12 33.69° 66.67% 1.2019
9/12 36.87° 75% 1.25
10/12 39.81° 83.33% 1.3017
11/12 42.51° 91.67% 1.3566
12/12 45° 100% 1.4142

Worked example

You measure 6 inches of rise over a 12-inch run. That is 6/12, or 26.57°. If the roof covers a 1,200 sq ft footprint, its surface is 1,200 × 1.1180 = 1,341.6 sq ft.

A note on flat roofs

A rise of zero gives 0/12, an angle of 0°, and a slope factor of 1, so the roof area equals the footprint. Real low-slope roofs are built with a slight fall for drainage, so a small non-zero pitch is more realistic than a true zero. Enter whatever you measure.

Frequently asked questions

What does 6/12 mean?

Six inches of vertical rise for every 12 inches of horizontal run. Doubling the rise to 12/12 gives 45°.

How do I measure pitch on a roof?

Measure a horizontal distance and the vertical rise over it. On a ladder or from the ground, a level and a tape work. If you cannot measure safely, use the building width and the height at the ridge.

Can I enter rise and run in feet instead of inches?

Yes, as long as both are the same unit. The result is still expressed per 12, because the ratio is what matters.

Does pitch decide which roofing material I can use?

It constrains it. Manufacturers set a minimum slope and different details below certain pitches, so check the installation instructions for the product rather than assuming.

Related