Measurement

Roof area calculator

Sloped roof area and roofing squares from the building footprint and the roof pitch.

Inputs

ft
Outside wall to outside wall, along the ridge.
ft
Across the gable ends, wall to wall.
rise / 12
Inches of rise per 12 inches of run. Enter 0 for a flat roof.

Roof planes only. The triangular gable end is a vertical wall. It is not roofing surface and is not counted here.

Results update as you type.

Result

2,683.28 sq ft L3 · Sloped roof area

L1
Footprint, 60 × 40 ft
2,400 sq ft
L2
Slope factor for 6/12
1.118
L3
Roof area, L1 × L2
2,683.28 sq ft
L4
Roofing squares, L3 ÷ 100
26.83

Slope factor = √(12² + rise²) ÷ 12. Counts roof planes only: gable-end walls, dormers and valleys are not included.

Calculated from the inputs on this page. Sources checked 21 Nov 2026.

A simple roof shape only. A rectangular footprint under a symmetric gable. Dormers, valleys, bays and separate wings add area and need their own measurement.

How this is calculated

A pitched roof has more surface than the ground it covers. The ratio between the two is the slope factor, and it depends only on the pitch.

L1 = length × width
L2 = √(12² + rise²) ÷ 12
L3 = L1 × L2
L4 = L3 ÷ 100

Each of the two planes is (width ÷ 2) × slope factor × length. Add both planes and you get the footprint multiplied by the slope factor. No area is added for the gable ends, because they are vertical walls rather than roofing.

Gable-end view showing which parts are roof surface A gable end seen from the side. The two sloped roof planes are the roofing surface. The triangle between them and the top of the wall is the gable-end wall, which is vertical and is not counted as roof area. pitch GABLE-END WALL vertical, not roof area ROOF PLANES, measured on the slope width
Figure 1. A gable end. The two sloped planes are the roof surface. The triangle under them is the gable-end wall: vertical, and excluded from the calculation.

Worked example

A building 60 ft long and 40 ft wide, with a 6/12 roof. The footprint is 60 × 40 = 2,400 sq ft. The slope factor for 6/12 is √(144 + 36) ÷ 12 = 1.1180. Roof area = 2,400 × 1.1180 = 2,683.28 sq ft, which is 26.83 roofing squares.

What this does not include

  • Gable-end walls. Vertical, and not roofing. Siding for them is measured separately.
  • Fascia and soffit. Trim, not roof surface.
  • Dormers, valleys and bays. Each adds planes that this rectangle does not describe.
  • Overhangs. The eave overhang adds surface. It is included in the rafter calculator but not here, because it does not change the footprint.

Frequently asked questions

Why is roof area bigger than floor area?

A pitched roof is longer along the slope than across the flat footprint. The steeper the roof, the bigger the difference. At 6/12 it is about 11.8% more.

Should I measure the footprint or the roof itself?

This calculator starts from the footprint because it is safer to measure from the ground. If you can measure the roof planes directly, use those measurements instead and skip the slope factor.

Does a flat roof work?

Yes. Enter a pitch of 0 and the roof area equals the footprint, because the slope factor is 1.

Is the gable end really excluded?

Yes. The triangle at each end of a gable roof is a wall. Counting it would overstate the roof by the area of two triangles.

Related