Materials

Shingle bundle calculator

Bundles to order from roof area, waste allowance and the coverage printed on your shingle bundle.

Inputs

sq ft
Measured on the slope, not floor area.
%
10% and 15% are common starting points. This is your choice, not a measurement.
Choosing a product fills the coverage field. Editing coverage switches this to “Other product”.
sq ft
The only coverage value used in the calculation. Check the bundle wrapper for your product.

The GAF preset is provisional. 32.8 sq ft is an average derived from GAF’s installation instructions, not a per-bundle specification, and the document covers several Timberline HDZ-family lines. Confirm it for your product before ordering, or enter your own coverage.

Results update as you type.

Result

81 bundles L5 · Bundles to order (L4 rounded up)

L1
Roof area
2,400 sq ft
L2
Waste, 10% of L1
240 sq ft
L3
Coverage needed, L1 + L2
2,640 sq ft
L4
Bundles before rounding, L3 ÷ 32.8
80.49

Coverage 32.8 sq ft per bundle (average, GAF installation instructions) · checked 21 Nov 2026 · source

Calculated from the inputs on this page. Sources checked 21 Nov 2026.

Field shingles only. Starter strip, hip and ridge caps, underlayment and fasteners are not included.

How this is calculated

Three numbers set the bundle count: the roof area, a waste allowance for cuts, and the coverage printed on the bundle. The result is rounded up, because suppliers sell whole bundles.

L3 = L1 × (1 + waste ÷ 100)
L5 = ⌈ L3 ÷ coverage ⌉

A conventional roofing square is 100 sq ft of roof. This calculator does not count squares. It divides by coverage per bundle, and for Timberline HDZ GAF’s installation instructions give a lower installed coverage: three bundles cover 98.4 sq ft, which is 32.8 sq ft per bundle on average. Using 100 sq ft per square instead would give 79.2 bundles and order 80, one short.

Bundle build-up with the example values Roof area 2,400 sq ft. Adding 10 percent waste gives 2,640 sq ft needed. Dividing by 32.8 sq ft per bundle gives 80.49 bundles before rounding. Rounded up, 81 bundles. ROOF AREA · L1 AREA + WASTE · L3 ÷ COVERAGE · L4 ROUND UP · L5 2,400 sq ft 2,640 sq ft 80.49 81 bundles
Figure 1. Bundle build-up with the example values on this page. Each box is one ledger line: L1 roof area, L3 coverage needed, L4 bundles before rounding, L5 bundles to order. The same numbers appear in the worked example below.

Worked example

Using the example values: 2,400 sq ft × 1.10 = 2,640 sq ft needed. Divided by 32.8 sq ft per bundle, that is 80.49 bundles. Rounded up, you order 81 bundles. Those 81 bundles cover 2,656.8 sq ft, which is 16.8 sq ft more than the 2,640 needed.

Source for coverage

The 32.8 sq ft figure is an average derived from GAF’s installation instructions for Timberline HDZ shingles: document RESTL622-PDF-0423 (© 2023), General Instructions. The instructions state that three bundles, applied as directed, cover 98.4 sq ft. 98.4 ÷ 3 = 32.8.

GAF does not state a per-bundle figure, so 32.8 is an average across the three-bundle set. It is an installed-coverage figure, not the 33.33 sq ft printed on retailer listings. The 33.33 figure is not verified by GAF as coverage and is not used here.

The document covers several Timberline HDZ-family lines, so confirm it applies to your product before ordering. A copy of RESTL622-PDF-0423 is hosted by a retailer. Checked 21 Nov 2026. Confirm the current version on gaf.com before relying on it.

Provisional preset. The GAF entry is offered because it is the only coverage figure on this site with a traceable document behind it. It has not been verified against gaf.com for each product line, so treat it as a starting point and check your bundle.

Assumptions and limitations

  • Counts field shingles only.
  • Assumes the area is measured on the slope.
  • Assumes the coverage figure matches your bundle wrapper.
  • Waste covers ordinary cutting. It does not cover a full re-deck, valley repair or a complex roof shape.
  • Check the count against your supplier’s takeoff before you order.

Frequently asked questions

How many bundles are in a roofing square?

GAF lists three bundles per square for Timberline HDZ. Its installation instructions say three bundles cover 98.4 sq ft, so this calculator uses 32.8 sq ft per bundle rather than a 100 sq ft square. Other products differ. Check the wrapper or the manufacturer’s data sheet.

Should I use 10% or 15% waste?

10% and 15% are common starting points, not measured values. Hips, valleys, dormers and many cuts usually call for more waste.

Does this include ridge caps and starter strip?

No. Starter, hip and ridge caps, underlayment and fasteners are separate products with their own coverage figures.

Why round up?

Suppliers sell whole bundles. A result of 80.49 means you order 81.

Related