Metal roofing covers a wide price range because “metal roof” describes several different systems. A through-fastened corrugated panel and a standing-seam roof with concealed clips are both metal, both sold by the square, and priced differently enough that comparing a quote for one against a quote for the other tells you nothing.
The useful question is not what metal costs on average. It is which system is being quoted, what it includes, and what has to happen underneath it.
What changes the price
Panel system. Exposed-fastener panels are screwed through the face of the panel. Standing-seam panels have raised seams and concealed clips, and the seams are formed or crimped after installation. Standing seam takes longer to install and uses more trim, so it usually costs more. Neither is automatically right for a given roof.
Panel thickness and finish. Steel panels are specified by gauge, and aluminium by thickness. A heavier panel uses more metal. The finish matters too: a painted steel panel and a mill-finish aluminium panel are different products with different warranty terms.
Coverage width. Panels are sold at a nominal width, but the installed coverage is narrower because seams and laps overlap. A supplier quoting “16-inch panels” is describing the panel, not the coverage. Ask for the coverage width, then divide the roof area by it to check the panel count.
Trim and flashing. Ridge caps, hips, valleys, eaves, gables, sidewalls and penetration boots are made from the same coil as the panels. Trim is often a meaningful part of the material total because a complex roof has a lot of edges, and it is easy for a quote to leave trim out of the headline price.
Underlayment and substrate. Metal roofs need a separation layer over the decking. Some systems use a synthetic underlayment; others use a high-temperature membrane where the panel gets hot. Condensation control matters as well, particularly over a ventilated attic.
Labour. Metal panels are long, awkward to handle and easy to damage. Cutting and bending on site requires the right tools, and a crew without experience with the specific system can void the manufacturer’s warranty. Skilled labour costs more per hour, and the job can take longer than shingles.
Removal and disposal. Metal is lighter than tile but heavier than asphalt shingles. If the old covering comes off, removal and dumpster costs apply.
What a metal quote should show
Ask for these as separate lines, or at least as identifiable quantities:
- Panel product, profile, gauge or thickness, and colour.
- Coverage width per panel, and the number of panels or lineal feet.
- Square footage of panel and the waste allowance.
- Trim: each type, in lineal feet, with the price per foot.
- Fasteners or clips, with the quantity and type.
- Underlayment, with the product name and the number of rolls.
- Decking repair allowance, if any.
- Removal and disposal.
- Permit.
- Labour.
- Manufacturer warranty documents and workmanship warranty.
A quote that lists only “metal roof, installed” has hidden all the decisions that determine the price.
Running the arithmetic
Take a 2,683 sq ft roof, or 26.83 squares. The rates below are made up to show how the lines combine. They are not market prices and should not be used as an estimate of what your roof will cost.
| Line | Arithmetic | Amount |
|---|---|---|
| Panels | 26.83 × $450 | $12,074 |
| Labour | 26.83 × $350 | $9,391 |
| Trim and flashing | allowance | $1,200 |
| Tear-off and disposal | 26.83 × $90 | $2,415 |
| Permit | flat | $450 |
| Subtotal | $25,529 | |
| Contingency, 8% | $25,529 × 0.08 | $2,042 |
| Total | $27,571 |
At about $1,028 per square, that total sits well above the asphalt example on our cost guide, which is what you would expect from a different system and a fictional rate. The point of the table is the structure: panels and labour scale with the roof, trim is an allowance, and the permit does not scale at all.
Put your own quotes into the replacement cost calculator and the same arithmetic runs with your numbers.
Comparing two metal quotes
Check whether both quotes describe the same panel system. A standing-seam quote compared against a through-fastened quote is not a comparison.
Check the coverage width and the panel count. Two quotes for the same roof should arrive at a similar lineal footage. A large gap usually means one supplier is counting nominal width instead of coverage.
Check the trim quantities against the roof’s edges. Count the ridge, the hips, the valleys and the perimeter in lineal feet, then compare with the quote. Missing trim tends to appear later as a change order.
Check the fastener specification. Exposed-fastener panels depend on the screw and the washer for their watertightness, and the wrong fastener for the substrate will fail. Standing seam depends on the clip, which allows the panel to move as it expands and contracts.
Ask who manufactures the panel and who profiles it. Some suppliers roll panels to length locally, which reduces seams and joints, and that is worth knowing when comparing price.
Weather and movement
Metal expands and contracts as it heats and cools. Standing-seam systems are designed for that movement, with clips that hold the panel while letting it slide. Through-fastened panels rely on the fastener hole and washer to accommodate it.
Snow behaves differently on a smooth metal surface. In regions with heavy snow, snow guards are sometimes specified to keep snow from sliding off in a sheet above a doorway or walkway. Whether they are needed depends on the roof, the climate and the building’s exits, and a quote should say whether they are included.
Rain noise is a common concern. It depends on the decking, the underlayment and the insulation below, so ask to hear an installed roof of the same system rather than relying on a description.
Is metal worth the difference?
That depends on what you are comparing and how long you plan to stay. Metal panels are lighter than tile and, in many systems, can be installed over an existing roof with the right substrate and code approval. Warranties vary by product and by finish, and the finish warranty is usually separate from the substrate warranty. Read both.
We do not publish energy savings figures, because the saving depends on the climate, the attic, the insulation and the existing roof, and a generic percentage would not describe your house.
The honest comparison is a whole-life one: what the system costs now, what maintenance it needs, how long the manufacturer will stand behind it, and what a future replacement would cost. Get that in writing rather than from a brochure.
Frequently asked questions
Why is a metal roof quote so much higher than shingles?
The materials cost more per square, the installation takes longer, and trim is a larger share of the job. How much higher depends on the system, the roof shape and local labour.
Can metal go over existing shingles?
Sometimes, if local code and the manufacturer allow it, and if the substrate is sound. Removing the old roof is often the safer choice because it allows the decking to be inspected.
Does a metal roof need a minimum pitch?
Manufacturers set a minimum slope for each profile, and the details at low slopes differ from those on steep roofs. Check the installation instructions for the specific panel rather than assuming.
How long does installation take?
A simple roof can be faster than shingles once the panels are on site, because large areas are covered at once. Complex roofs with many penetrations and valleys take longer. Ask for a schedule in the contract.
What about hail and dents?
Steel and aluminium behave differently under impact, and finish warranties sometimes exclude cosmetic damage. Ask what the warranty covers before you choose a panel.