Guide

Roof pitch chart: common roof slopes explained

Pitch is written three ways depending on who is asking. This guide converts between rise per 12, degrees, percentage and slope factor, and explains where each one is used.

Reviewed 21 Nov 2026 By the usroofwala editorial desk US customary units

Quick answer

Roof pitch is the rise over 12 inches of run. A 6/12 pitch rises 6 inches for every 12 inches across, which is 26.57 degrees, a 50 percent slope, and a slope factor of 1.1180. Multiply a flat footprint by the slope factor to get sloped roof area.

Ask three people for a roof pitch and you may get three answers. A framer says “six twelve”. An architect says “twenty-six and a half degrees”. A specification sheet says “50 percent slope”. They are describing the same roof.

The chart below converts between them. Every value is calculated from the same formulas the pitch calculator uses, so the table and the tool agree.

What x/12 means

Pitch in the x/12 form compares vertical rise to a fixed horizontal run of 12 inches. A 4/12 roof rises 4 inches over every 12 inches of horizontal distance. The run is always 12 in this notation, which makes it easy to compare one roof with another without knowing the size of the building.

The angle is the arctangent of rise divided by run. The slope percentage is rise divided by run, multiplied by 100. The slope factor is the length along the slope divided by the horizontal length, and it is the number that converts flat area into roof area.

Pitch chart

Pitch Degrees Slope Slope factor
0/12 0.00° 0.00% 1.0000
1/12 4.76° 8.33% 1.0035
2/12 9.46° 16.67% 1.0138
3/12 14.04° 25.00% 1.0308
4/12 18.43° 33.33% 1.0541
5/12 22.62° 41.67% 1.0833
6/12 26.57° 50.00% 1.1180
7/12 30.26° 58.33% 1.1577
8/12 33.69° 66.67% 1.2019
9/12 36.87° 75.00% 1.2500
10/12 39.81° 83.33% 1.3017
11/12 42.51° 91.67% 1.3566
12/12 45.00° 100.00% 1.4142

Why the slope factor matters

The slope factor is the ratio of roof surface to footprint. A 2,000 sq ft footprint under a 6/12 roof has 2,000 × 1.1180 = 2,236 sq ft of roof surface.

The effect grows with pitch. At 4/12 the factor is 1.0541, so the roof is about 5 percent larger than the footprint. At 12/12 it is 1.4142, about 41 percent larger. Ignoring the factor on a steep roof understates the area, and therefore the shingles, by a wide margin.

The same number converts horizontal distances into lengths along the slope. A rafter run of 12 ft at 6/12 is 12 × 1.1180 = 13.42 ft to the wall line.

How to measure pitch

The safest method uses a level and a tape at the gable end or from a window. Hold the level horizontally, mark a 12-inch run, and measure the vertical distance from the end of the level down to the roof line. That vertical distance in inches is the pitch.

From inside an unfinished attic, the same measurement works on the rafters: 12 inches horizontally along a rafter’s run, then the vertical rise over that distance.

From the ground, you can estimate from the building width and the height at the ridge. Half the width is the run, and the rise is the ridge height above the eaves. Divide the rise by the run and multiply by 12 to get the pitch.

Do not walk a roof to measure it. OSHA requires fall protection for workers in residential construction at six feet or more above a lower level, and the hazard applies to anyone on the roof. A measurement taken from the ground is accurate enough for planning material.

Converting degrees to pitch

If you have an angle in degrees from a digital level or a drawing, the conversion is:

rise per 12 = tan(degrees) × 12

A 30-degree roof is tan(30) × 12 = 6.93/12. A 45-degree roof is 12/12, because tan(45) equals 1.

Going the other way, pitch to degrees:

degrees = arctan(rise per 12 ÷ 12)

Flat and low-slope roofs

A pitch of zero is a real input. The calculator accepts it, and the slope factor becomes 1, so roof area equals the footprint. On an actual building, a roof described as flat almost always has a slight fall for drainage, so a small non-zero pitch is more realistic than a true zero.

There is no single slope value that everyone agrees marks the boundary between low-slope and steep-slope roofing. Manufacturers publish minimum slopes for their products, and codes and insurers may use their own thresholds, so check the instructions for the material you intend to use.

Where pitch changes the job

Pitch affects more than area. Steeper roofs are slower and more hazardous to work on, so labour costs rise. Some materials are approved only above a certain slope. Ventilation details and ice barrier requirements can change with pitch. Waste allowances often rise with complexity, and pitch is part of that complexity.

For planning, the practical order is: measure the pitch, use the slope factor to get the sloped area, then buy material for the sloped area. Doing it in the other order, measuring area and guessing at pitch, is where most takeoff errors start.

Frequently asked questions

What is the most common roof pitch?

There is no universal answer, and any figure would depend on the region and the era of construction. For your own roof, measure it. The chart covers every pitch from flat to 12/12.

Is a 6/12 roof steep?

It is a conventional pitched roof, walkable with care by experienced crews under fall protection. “Steep” in roofing usually refers to roofs where standard installation methods change, and that threshold is set by the manufacturer, not by a general rule.

Can I use degrees directly in the area calculator?

The area calculator takes rise per 12. Convert degrees first with tan(degrees) × 12, or use the pitch calculator to do it.

Does a steeper roof last longer?

Pitch affects drainage, which affects how long water sits on the surface, but roof life depends on the material, the installation, the ventilation and the climate. Pitch alone does not determine lifespan.

Run your own numbers

The arithmetic here is the same arithmetic the calculator uses, with your measurements instead of the example ones.

Open the roof pitch calculator

Sources

Checked 21 Nov 2026. Links open in a new tab.

  1. OSHA 29 CFR 1926.501, Duty to have fall protection